IS Series Single-Stage Centrifugal Pump, Without Blockage Booster Pump

IS Series Single-Stage Centrifugal Pump, Without Blockage Booster Pump

Introduction

1. IS clean water pump is mainly composed of pump body, pump cover, impeller, shaft, seal ring, bushing and suspension bearing components.
2. The housing of the IS centrifugal clean water pump (ie the pump body and the pump cover) constitutes the working chamber of the pump. The impeller, shaft and rolling bearing are the rotor of the pump. The suspension bearing component supports the rotor portion of the pump, which is subjected to the radial and axial forces of the pump.
3. The pump body and pump cover part of the IS centrifugal clean water pump are divided from the back of the impeller, which is commonly referred to as the rear open door structure. The advantage of the pipeline centrifugal pump is that it is easy to overhaul. During the inspection, the pump body is not moved, the suction pipeline, the discharge pipeline and the motor are removed. Only the intermediate coupling of the extension coupling can be removed, and the rotor portion can be taken out for maintenance.
4. The axial seal ring of IS centrifugal clean water pump is composed of packing gland, packing ring and packing to prevent air intake or a large amount of water leakage. If the impeller of the IS pump is balanced, the cavity with the soft packing is connected to the suction port of the impeller. If the liquid at the inlet of the impeller is in a vacuum state, it is easy to enter the air along the surface of the sleeve, so a packing ring is installed in the filling chamber. The pressure in the pump chamber is led to the packing ring through a small hole in the pump cover for sealing. If there is no balance hole in the impeller of the pump, since the liquid pressure on the back of the impeller is greater than atmospheric pressure, there is no gas leakage problem, so the packing ring may not be installed.
5, IS centrifugal clean water pump to avoid shaft wear, the shaft is protected by the bushing at the part of the shaft through the packing cavity. An O-ring seal is provided between the sleeve and the shaft to prevent air intake or water leakage along the mating surface.
6. The transmission mode of the IS centrifugal clean water pump is connected with the electric motor by lengthening the elastic coupling. The rotation direction of the pump is rotated clockwise from the driving end.
7. IS centrifugal clean water pump In order to balance the axial force of the pump, most pumps have a seal ring on the front and rear of the impeller, and a balance hole on the rear cover of the impeller. Because some pumps have little axial force, There are no seal rings and balance holes on the back of the impeller.

Model Meaning

eg:IS 80 - 65 - 160 A

IS---------IS Single Stages Single Suction Clean Water Centrifugal Pump

80--------Suction Diameter(mm)

65--------Discharge Diameter(mm)

160-------Impeller Nominal External Diameter(mm)

A----------Impeller Processed With First Cutting

Product characteristics

1. The IS type single-stage single-suction centrifugal pump is designed according to the performance and size specified in the international standard ISO2858. It is mainly composed of pump body, pump cover, impeller, shaft, seal ring, bushing and suspension bearing.

2. The pump body and pump cover part of the IS type single-stage single-suction centrifugal pump are divided from the back of the impeller, which is commonly referred to as the rear door structure. The utility model has the advantages that the maintenance is convenient, the pump body is not moved during the maintenance, the suction pipeline, the discharge pipeline and the electric motor are removed, and only the intermediate coupling member of the extension coupling is removed, and the rotor portion can be taken out for maintenance.

3. The pump housing (ie pump body and pump cover) forms the working chamber of the pump. The impeller, shaft and rolling bearing are the rotor of the pump. The suspension bearing component supports the rotor portion of the pump, which is subjected to the radial and axial forces of the pump.

4. In order to balance the axial force of the pump, most of the impellers of the pump are provided with a sealing ring at the front and the rear, and a balance hole is arranged on the rear cover of the impeller. Since some pumps have little axial force, the back of the impeller is not sealed. Ring and balance hole.

5. The axial seal ring of the pump is composed of packing gland, packing ring and packing to prevent air intake or a large amount of water leakage. If the impeller of the pump is balanced, the cavity with the soft packing is connected to the suction port of the impeller. If the liquid at the inlet of the impeller is in a vacuum state, it is easy to enter the air along the surface of the sleeve. Therefore, a packing ring is inserted in the filling chamber. A small hole in the pump cover guides the pressurized water in the pump chamber to the packing ring for sealing. If there is no balance hole in the impeller of the pump, since the liquid pressure on the back of the impeller is greater than atmospheric pressure, there is no gas leakage problem, so the packing ring may not be installed.

6. In order to avoid shaft wear, bushing protection is provided at the part of the shaft passing through the packing cavity. An O-ring seal is provided between the sleeve and the shaft to prevent air intake or water leakage along the mating surface.

7. The transmission mode of the pump is connected with the motor by lengthening the elastic coupling. The rotation direction of the pump is rotated clockwise from the driving end.

Structure Description

Shijiazhuang ShizaPump Industry Co.,Ltd. founded in 2008, is a professional industrial pump manufacturer engaged in researching slurry pump, wear and corrosion resistant materials and OEM processing.

Shizapump group covers more than 40000 square meters, the registered capital is 18 million yuan. Over the years with strong strength and people-oriented concept, we absorb a large number of high-quality management and technical talents. Existing staff is more than 220 people, of whom 30% are technicians.

Our production area covers an area of 24000 square meters, the total production capacity of an annual output is 10000 units (sets), and the annual output of all kinds of high chromium alloy castings is 2000 tons.The production area is divided into five districts one area and two centers, namely mould casting, heat treatment, fine machining, forge welding and assembly coating of five production areas; finished spare parts; quality analysis and water experiment. The main material of products: A05, A49, A33, A51 and other high chromium white cast iron.

Shijiazhuang ShizaPump Industry Co.,Ltd. fully implements the ISO9001 management system and observes the process of inspection. Quality inspection records are available in all production processes. Professional instruments include spectrometer, metallographic analyzer, flaw detector, mechanical test machine (strain, impact, hardness), magnetic flowmeter, pressure gauge, ammeter, vibration meter, noise meter, hydraulic experimental curve of professional software. Perfect detection guarantees the quality of equipment to ensure that each pumps and parts are fully in line with the requirements.

Shijiazhuang ShizaPump Industry Co.,Ltd. has spread all domestic market in China over 30 provinces and municipality. Also has been successfully used in 20 countries in global .First line staff have professional experience to provide service for customers.